Circuit Design Jobs

Need skills: karnaugh map, JK flip-flop counters, design a digital system and draw the schematics on paper. I need you familiar with designing digital systems. Also on design/ draw the schematic. Xilinx.

I have pt100 temperature sensor signal connected to plc put the signal is not stable as there is many noise come from vfd so I need low pass filter circuit to enter the pt100 signal on it to make filter of any other noise

I have a preliminary design for a custom smart plug that potentially incorporates an additional feature that has never previously been incorporated with one. I want to find someone who can verify the design, help incorporate the new feature, and provide the necessary drawings for this initial prototype.

I have PADS Pro project files which have the schematic and component placement on pcb. I need a PCB designer who can finish the layout design. Need to start immediately due to urgency.

Need to use Stm cube 32,IAR workbench,logisim

We need to make a gerber file for our pcb setup. it will be to contact 16 spring contacts and a set of two square eights pin contacts. :) The last two photos is of the original pcb we are trying to replicate. the problem with this one is that it only has eight spring contacts and only holds a sample that is 25x25mm we need it to have 16 contacts instead of eight and it being able to measure 8 points of a 100x40mm sample. the distance between the spring contacts should be 1cm center to center side ways. See the photos if you have any questions or send a question thru here.

Need to design voltage amplifier

Design Temperature RECORDING AND CONTROLLING SYSTEM WITH Dash board

Hi I need a motherboard PCB with a DC DC converter from 12V to 5V. It will be attatched to the motherboard: * Rasberry PICO * Can PCB * 6 buttons * 9 LED The DC DC converter need to have short circuit protection and the Canbus connector need TVS diode. Se the files for more information. Step 1. Make a chematics Sted 2. Make a PCB with production files

Hello! I need a PCB Layout designer for MFRC522 (RFID) from the MPN Datasheet.

start with -> i am not a bot. I need a 2kW design for DC to AC inverter. Schematic, plus layout and source code.

Note: I'm looking for developers that have previous experience with GreenPak ICs I have a sensor that consumes ~300uA at 3.3v and I need to reduce it's power consumption by duty cycling it. The GreenPak design will need to power up the sensor, read the differential analog output, store the number of changes in a counter then power down the IC. The counter will be available via I2C for an external CPU.

Hello I mainly need a knowledgeable person in PCB design to help with import an old project from CADint and edit it on Orcad. Most of the work will be mainly on Orcad PCB design. Please do not bid if you are not good enough on Orcad

I need a soldering job USB port has come off cleanly from a circuit board. I need to bring this to you and have you do the work. I don’t really want to post away if I can help it.

We need to build a circuit to read the rfid card as per the attached requirement document.

WE NEED WEIGHING SCALE PCB BASED ON 24 BIT 1232 ADC AND HX710 with 8 BIT MICROCONTROLLER 1.ADC- HX 710A AND 1232 2.MICROCONTROLLER- ANY ONE Easy Available and IN PRICE 7 SEGMENT 7 DIGIT COMMON ANODE DRIVER .

Looking for knowledgable guy to help with 1mA current source circuit

I a close focal point camera (50mm) with Bluetooth that will be set ready to go when power (12v) is supplied and transmit vision via Bluetoothed to a device. I would like this unit to have a GPS which will transmit when vehicle is in motion. The unit will be installed in a camper van and used for set-up.

Please Sign Up or Login to see details.

require to route a pcb with component placement in easy eda

We need a PCB Designer to help me to develop the project together. Our talented team is our greatest asset. We provide opportunity, reward performance, and support a positive and balanced work environment. Work from home.

Electrical engineer required having expertise in IC design and simulation with short report

Se trata de desarrollar una Carrier Board para el SoM de Radxa ROCK 3 Compute Module con el que disponer de conexiones Ethernet, Alimentación 12Vdc, HDMI, RS485, CAN Bus.