Deepak G. Profile

0.0

(0 reviews)

You're now following

Error following user.

This user does not allow users to follow them.

You are already following this user.

Your membership plan only allows 0 follows. Upgrade here.

Successfully unfollowed

Error unfollowing user.

You have successfully recommended

Error recommending user.

Something went wrong. Please refresh the page and try again.

Email successfully verified.

$5 USD / hour

jaipur,

india

$5 USD / hour

It's currently 12:40 PM here

Joined April 25, 2016

0 Recommendations

Deepak G.

@deepakgupta1

0.0

(0 reviews)

0.0

$5 USD / hour

jaipur,

india

$5 USD / hour

N/A

Jobs Completed

N/A

On Budget

N/A

On Time

N/A

Repeat Hire Rate

Shavie skill Development Center

I am a perusing (PhD) Doctor of Philosophy in Engineering from world renowned Institute IIT Delhi. I am expert in Data entry, file conversion, file formatting, logo designer for company and business card. I have my own team to work , so your task will be completed as early as you think. My work will give you guarantee for full satisfaction and if not then full money would be refund on disagree from my work except the transaction charges . I will also give you a future scheme such as 1- Within 01 month after the task completion, if any small change will be required in task then it will be free of cost. 2- If you assign me any task for the second time or 3rd time or in continuum then you will have some discount from my current charge definitely.

See all Copywriters in India

Contact Deepak G. about your job

Reviews

Changes saved

No reviews to see here!

Education

M.Tech

Malaviya National Institute of Technology,

India

2011 - 2013

(2 years)

B.Tech

Doctor Ram Manohar Lohia Awadh University,

India

2005 - 2009

(4 years)

Publications

Tribological behaviour of ball bearing in induction motors at varying speed condition

17th Asian Pacific Corrosion Control Conference (APCCC17)

The present investigation deals with important aspects of rolling contact tribology in bearing failures. Bearings are referred to as anti-friction bearings due to the low friction and hence only slight energy loss they cause in service, especially compared to sliding or friction bearings. Sliding wear of bearing grade steel balls (SKF 6204) is systematically investigated in automotive oil lubrication at varying load against NiCr steel.

Household Waste Transportation & Management by Intelligent System”,

International journal of Global Research in Science & Technology

In 21st Century it is a big issue of huge amount of household waste transportation in India.Whatever we consume generates a lot of garbage and waste. Discarding of products adds to the clutter of the dustbins. But what happens with this garbage is a thought less pondered upon.Wesee that everywhere the dustbin are full from garbage/waste material due to which the wastage is spread out around that dustbin, and it becomes a permanent place for disposal of garbage .

Electricity Generation Based on Pressure Retarded Osmosis: A Review

International journal of Global Research in Science & Technology

Energy consumption is an important aspect in our day to day life. So it’s time to look for more sources of energy rather than the non-renewable sources of energy and reduce the rate of consumption of non-renewable energy. Osmotic power or pressure retarded osmosis is the energy available from the difference in the salt concentration between seawater and river water.Pressure retarded osmosis (PRO).

Degradation Behaviour of Nano Structured Coatings Deposited by Physical Vapour Deposition

International journal of Global Research in Science & Technology

Degradation of the components used at elevated temperature due to erosion corrosion are recognized as serious problems in coal based power generationequipment. High temperature corrosion is a severe problem which may result in premature failure of the HSLA(High Strength Low Alloys) steel. One countermeasure to overcome this problem is the use of Nano structured protective coatings.

Development of a Fuzzy Model for Predicting Load Constant and RWL in Manual Material Handling Tasks

International Journal of Global Business and Competitiveness

Human centred system (HCS) is understood as the system of Human-Machine-Environment where the people at work have their relations with the surrounding environment, equipment, fellow workers and their work. The analysis of such systems can be performed aiming at different goals such as safety, health, human reliability, stress or usability.