Electromagnetic Coil Heating 2

$250-750 USD

Completed

Posted

almost 5 years ago

$250-750 USD

Paid on delivery

Please review this video. It is 6 minutes and twenty-nine seconds in length It is found at. [login to view URL] Use of an electromagnetic coil to heat water in a ferromagnetic (steel) pipe. The pipe is one inch in diameter and just long enough to be surrounded by ten windings of electromagnetic copper coils. Please refer to video for description of electromagnetic coils. Please advise the actual amperage needed to heat the water in an iron or steel pipe one inch in diameter and just long enough to be covered by 10 windings of copper coil to 250 degrees Fahrenheit. Two millimeter copper wire was used. For the 250 degree Fahrenheit temperature I am seeking, do I need ten windings of the wire? How many amps would ten windings require? How many amps would three windings require? The one inch pipe is still to be long enough to be covered by ten windings of wire. The video suggests that 12 volts (DC?) and three amps are enough to reach 166 degrees Celsius. Is this correct? Would there be enough heat energy to heat the water in the tube? Also, the video shows a solid section of iron. I am trying to heat a pipe containing water. Does this change the amperage required? Please specify the diameter of the copper wire used in the coil. Would it be 2mm? Also, what is the outside diameter of the windings? Is the iron tube heated by the near magnetic field or the far magnetic field? Is the white tube shown in the video necessary? What will be the diameter of the copper coil windings? The water will change to a steam state. What happens to the steam is the subject of a different study. The assignment is to determine the amperage needed to raise the temperature of the water to 250 degrees Fahrenheit starting in a fifty-degree Fahrenheit atmosphere. The secondary part of this project is to determine the amperage needed to heat water in the same tube to 250 degrees Fahrenheit using instead a resistance heating wire inside the same tube. I need a comparison of the two methods. Is the amperage the same whether the electric current is provided by a 12 volt DC battery or a 120 Volt AC 15 Ampere wall outlet as used in the USA with an inverter to create DC current? Please provide copy of your calculations.

Electrical Engineering

Project ID: 19806381

About the project

7 proposals

Remote project

Active 5 yrs ago

Looking to make some money?

Email address

Benefits of bidding on Freelancer

Set your budget and timeframe

Get paid for your work

Outline your proposal

It's free to sign up and bid on jobs

Awarded to:

@EasttecknosLtd

Hi there, I will provide detailed report containing all computation as per your description. Am well vast in electromagnetic systems,energy induction and related electromagnetic system and thus will provide adequate support in which will run from computation ,software validation of same calculation(HFSs,Comsol,Ansys maxwel) to product prototyping if need be. Kindly contact. Thank you

$300 USD in 7 days

4.6

(7 reviews)

4.3

7 freelancers are bidding on average $468 USD for this job

@SEELaboratory

Hi, I was very interested in your project. I was working on a similar device - boltbooster. The transfer of energy occurs near magnetic field. I have both the opportunity to do an experiment, and to make calculations, to do a simulation. If you are interested in my bid, I will be happy to answer your questions.

$250 USD in 7 days

5.0

(15 reviews)

6.5

@chuledeco

Hello! I introduce myself, I'm an electronic engineer with 10 years experience in the electronics design field. Also, I'm a physics teacher at the Engineer Faculty of the National University of Mar del Plata. I work in 'Physics B' subject which leads with the electromagnetism. I'm very familiar with Maxwell Laws of electromagnetism and obviously Faraday's law of induction. At this point, I need to tell you that all those values you need have hard depending on some geometric configurations. So, to have very approximate values we need to go throw the construction or the simulation of the device. I want to have a chat with you to accord some points. I can offer you make the calculation or the construction depending on what you need. My bid is only to feel the blank. The final budget will be delivered after discussing some points. NOTE: I loved this youtube channel.

$555 USD in 10 days

5.0

(17 reviews)

4.7

@jguzmanaladro

It is heating by magnetic induction, with high frequency the pipe is heated and this in turn heats the water, it can occupy a 110 volts, a rectifier source, the high frequency generator, a temperature control, the same magnetic induction makes the coils are overheated and can get to burn, so you have to control this point, some water heaters by induction, the same water is used to cool the coils, which are made of copper pipe and through them circulate the water. everything can be done, it's not that complicated. The calculations depend on how much water will circulate in the heated, this to calculate the power of the system.

$698 USD in 10 days

4.6

(1 review)

3.8

@delcti

Hello, my name is Diego, I am the owner of Accuracy FEA, we are dedicated to research and development in projects of engineering. We perform simulations with Comsol and Ansys, as well as numerical analysis with MATLAB. I have made several projects of water heaters by electromagnetic induction, among them are two of my inventions, one mechanical and the other resonant electric. I suggest you check my profile on Freelancer about the FEA projects, there you will find these projects. I am a freelancer preferred and certified, all comments are 5 stars. We carry out simulations in different areas, for your project I recommend to approach it with COMSOL since it is specialized in research and has many tools that allow you to reach the most complex objectives. I guarantee excellent results and a high level of detail in the technical documents. I would like to be able to work on your project, I hope your contact. thank you very much.

$470 USD in 5 days

5.0

(2 reviews)

2.8

@zaraza73

I am an electrical engineer, MSC in applied mathematics, MSC in power systems, PHD. Control and automation. I can do your project at any level, with all the details you need, within my proposal, I can offer you additional extras. with 23 years of experience. I can improve any proposal made by another, with a mutual agreement. I have already worked with this type of inductors to heat autoclaves, water heaters, steam generators, heat treatment and induction cookers, we can discuss the details of your needs in the chat. I have several circuits ready and tested to work I have already done this type of project for this application the matlab, labview, and others. I'm interested in your project Atte. ING. Luis Moreno

$750 USD in 7 days

0.0

(0 reviews)

0.0

@hosseinskandari

Hi, We are a team of experienced electrical Engineers. Our proficiency is Electromagnetics. We offered the lowest price in order to complete the resume of our recently created account. Also we proposed 10 day delivery to write a complete report for you again to have a good review from you. We will be happy to help you. Bests.

$250 USD in 10 days