Esp8266 mikroc jobs

This project will send command to arduino module via Bluetooth and WiFi connection using HC-06/HC-05 module and ESP8266 WiFi module. For demo please see the video below: Google Play

esp8266 esp-12E hardware only Arduino C++ environment, 3 outside sensors (2xHi/Low state + 1xADC) RGB ws2811 working by 10 different algoritm Functions - FOTA, deep sleep, wake up by sensor, Wifi AP with settings to client and reset, NTP time synchronising, alarm settings. All algoritm settings (about 20 parameters) will be in esp8266 web server browser. Save settings to EEPROM memory. I created design of screen for settings and options.

Hello! I'm looking for hire someone to help me design and production a PCB for dual stepper motor driver arduino, and I've drawn a Schematic, and I still require some extra features from my layout as below. 1. support Bluetooth for HC-05 2. support ESP8266 3. design it as Compatible with arduino shield and other Mircocontroller 4. support recharge battery with control switch for on-board power 5. screw-less PCB terminal for stepper motor wire 6.2 chips for the driver of the motor. (SN754410) with IC socket 7. The voltage converter 5V-> 3.3V for UART communication module using LD10863VV 8. etc.. If you think you, you can make these requirement function. Please contract me. Thanks

Summary The main concept is to deliver cheap and reliable IoT device with a set of measuring sensors. The device must have WiFi configurable as an Access Point by default and simple re-configuration for connection to home network. As a development kit will use NodeMCU, which is based on ESP8266 chip. Hardware Customization Power Supply Module: AC 110V 60Hz => DC 5V (VTX-214-003-105) Linear Regulator: DC 3.3V 500mA ESP8266 ESP-12 Reset button Internal Recovery Connector Set of sensors: Temperature/Humidity (), Barometric Pressure (~), CO2 (MQ135, MG811) and CO/Methane (

i am working on avr/arduino based 3 led controller. Budget : 50-70$ My Setup : Arduino , atmega8,esp8266,static IP for each arduino is given. attached external I2C EEPROM Each arduino has 3 LED's , currently running basic firmware to turn on-off LED's via Esp8266 WiFi Requirement: Arduino code for : 1. Control from internet /IP 2. Firmware should be scalable for similiar multiple devices/ not hard coded for particular arduino. time via WiFi 4. GET/POST Data to webserver hosted on cloud. 5. architecture should be compatible with android/iOS SDK. This is test project , once the freelancer's code is verified , we have multiple features to be implemented in later versions to be posted as new/extended job . Freelancer's with past wor...

I have a NodeMCU ESP8266 WiFi V1.0 which works as a wifi access point with a simple web page. I have 2 arduino sketches that i would like activated from a buttons that will be loaded on the NodeMCU ESP8266 WiFi V1.0 web server. Two buttons on the web page to send commands to the esp8266 to activate relays

We are looking for someone who has knowledge in building firmware for the ESP8266 by using the Espressif SDK (if possible newest version) Project target is to setup building environment (Windows or Linux) and include an HTTP weblogin page (like esphttpd) where user can choose WIFI network and connect to it. We need someone who can start immediately

Looking for a person to work on a Android app which will connect to the hardware (ESP 8266) and transfer data both ways. The app will also communicate with the Java web server and send and receive data. More information would be provided later.

Develop a sensor that wakes up from sleep on a pin change, reads an analog value, or a digital pin status and send it via Wi-Fi to a webservice. The webservice address, username and password must be configurable after a button is pushed. After the button is pushed, the module enters in Access Point mode and exposes a simple website with 3 inputs address,username,password that will be saved in the Mcu eeprom and used after the reset to connect to the webservice.

Hi luvocean1, I need some help building sensor nodes with the ESP8266 module. The software should be based on the nodeMCU firmware, collect sensor data thru i2c, SPI or analog and transmit that data using a very simple web service. Functions like battery monitoring and advanced configuration should be added later. For starters the SparkFun ESP8266 Thing should be used, later on I will provide you with a custom board. Could you support me with this project? I would like to pay you on an hourly basis and provide any hard-/software you might need. If you're interested I would need you to sign an NDA and Code of Conduct (sadly thats a german regulation thing). Thanks for your reply, Christopher

need to program a wifi chip to build up a self configured mesh network using lua language. 4 chips are needed to be configured and the chips are ESP8266.

need to program a wifi chip to build up a self configured mesh network using lua language. 4 chips are needed to be configured and the chips are ESP8266.

We are looking for help at an urgent project. The taskt is to integrate an HTTP-Server (like ) in a slightly modified Nodemcu firmware (). Target that the firmware is running Nodemcu but the user has the possibility to configure WIFI over a SoftAP http-server. We would need anyone who can start immediately and has already experience in working with the ESP SDK. We will provide an Ubuntu based Virtualmachine (Virtualbox) which is ready to build Nodemcu.

Design a custom pcb combining arduino micro or similar at 3.3v and esp8266 (like catus micro does) with other few customizations. We will need the gerber 274-X data and NC drill files (eagle and other software can produce this kind of files) as well as all the specs necessary to send the design to a pcb manufacturer. We can provide the schematics of the different modules to integrate this PCB. The design must be as small as possible.

I want an raspberry pi with web server. i will control ON/OFF action through web based app on mobile/Tab/laptop. The raspberry pi need to control Light, fan, Tv (through IR blaster), etc.. I would prefer if u use ESp 8266 to control end pheripheral. I would also like to have temp. sensor data on tab. Please mention the time frame, total nos. of raspberry pi, arduino, esp8266 u require to make this possible. also i need to use capacitive touch buttons. following requirement: 4 lights 2 fans (with increase decrease) 1 socket 1 ir blaster to control TV. I want to control my bedroom. Also it dhould have easy expansion facility to add new device as and when required. I want the project to be complete wireless. (I will replace my current mwchanical switchboard with the switch panel...

I need a library for mqtt communication for PIC 18f microcontroller. the library should be able to publish/subscribe/implement QOS all three levels.

I need you to develop some software for me. I would like this software to be developed for Windows using C or C++.MikroC pro for AVR based ::On the output, the LED blinks once five seconds. if i press "A" on a Keyboard, it blinks once a seconds meanwhile. if i press "B", it goes back to main loop again. i think it requires UART Interrupt. Thanks.

Hi! I am looking for someone (the code should be easy but I'd prefer someone with experience) for coding the following: I need the ESP8266 SP07 search for the APs and write via serial on the UART the first 4 MAC address and their signal, like this: "MAC1",signal_MAC1","MAC2",signal_MAC2","MAC3",signal_MAC3","MAC4",signal_MAC4",A (the "A" is the end character). This have to be done firstly at the boot, an then in loop every 50 sec. Thank you

Hi! I am looking for someone (the code should be easy but I'd prefer someone with experience) for coding the following: I need the ESP8266 SP07 search for the APs and write via serial on the UART the first 4 MAC address and their signal, like this: "MAC1",signal_MAC1","MAC2",signal_MAC2","MAC3",signal_MAC3","MAC4",signal_MAC4",A (the "A" is the end character). This have to be done firstly at the boot, an then in loop every 50 sec.. Thank you

I'd like to get a MikroC Pro TCP/IP Stack Implementation for the PIC18 series, very similar to the library provided by Microchip. The library must support the same protocols (TCP,UDP,ARP, IP, ICMP, UDP, TCP, DHCP, SNMP, HTTP, FTP, TFTP,SSL)as the Microchip library and work with MikroC v3.80 and up. I need full source code and API documentation. Basicly it could be the same as microchip stack but ported to mikro C compiler. Regards

I am learning ESP8266 and I know there are people who have gotten up the curve faster than I have. I need someone who has done some projects with this chipset to create and share code for a simple momentary switch that will drive a low voltage relay. I would like to have someone walk be through putting the switch on or similar site. This is basically customized tutoring for me so I would like to have demostrated source code, help through teamview loading on the device, setup of thingspeak (or similar), and finish with a fully demonstrable device. I have a few devices so we can load and I can share my screan for error checking. This is to help me learn so I will need to keep the budget below $50.

I need a PCB schematic and layout designs for simple IoT device. BOM is in attached file. Device uses temperature sensor and a relay to control an electric motor. Controlling software runs on ESP8266 WiFi module. Files to be combatible with a freeware (DesignSpark, Eagle Lite).

We are going to use the ESP8266-12 module as a controller, and control by the mobile (IOS or Android), the control is simple as send your information by TXD&RXD, control it ON/OFF by GPIO pin, reading or write the voltage by ADC/DAC pin. We will talking the details with the right person.

I need Arduio uno R3 code which can measure the temperature and humidity with DHT22 sensor, and this arduino can connect to WIFI AP with ESP8266 Uart Serial to Wi-Fi Wireless Module. Furthermore I can read the measured datas from this Arduino with "REST API" example: GET http://arduinoIP/temperature and I get the temperature valule in celsius.

When we are connecting to server using ESP8266-01 module using AVR controller, at baud rate 115200, it stops responding after sometime. We need someone to fix this bug.

I need a 256 bit sine wave code for pic micro controller 16F628A. The signal should be of 15khz for sine wave. I am using an H-bridge at the PWM output of the micro controller to convert it to ac wave and then using a transformer to step it up 230 vac with capacitor filter to give me pure sine wave.. The program must me written in mikroC pro and each line must be annotated

I need a 256 bit sine wave code for pic micro controller 16F628A. The signal should be of 15khz for sine wave. I am using an H-bridge at the PWM output of the micro controller to convert it to ac wave and then using a transformer to step it up 230 vac with capacitor filter to give me pure sine wave.. The program must me written in mikroC pro and each line must be annotated

Hello! I need a footprint drawings for Altium Designer, list of the components: - Bluetooth BLE HM-11 - WI-FI Module ESP8266 - ESP-01 - LCD 1602 HD44780 - Temperature and humidity sensor DHT11 - Light sensor - Gyro sensor - Smoke MQ2 sensor - touch button (to switch on/off) TTP223B All modules must place on board horizontally through holes.

Hello! I need a footprint drawings for Altium Designer, list of the components: - Bluetooth BLE HM-11 - WI-FI Module ESP8266 - ESP-01 - LCD 1602 HD44780 - Temperature and humidity sensor DHT11 - Light sensor - Gyro sensor - Smoke MQ2 sensor - touch button (to switch on/off) TTP223B All modules must place on board horizontally through holes.

Hello! I need a footprint drawings for Altium Designer, list of the components: - Bluetooth BLE HM-11 - WI-FI Module ESP8266 - ESP-01 - LCD 1602 HD44780 - Temperature and humidity sensor DHT11 - Light sensor - Gyro sensor - Smoke MQ2 sensor - touch button (to switch on/off) TTP223B All modules must place on board horizontally through holes.

I need a sensor to work with the easyiot platform found :// I need it done using the esp8266 wifi module and a hx711 load cell amp so i can have a weight sensor on the easyiot platform. There are arduino librarys for the hx711 load cell amp.

I would like a small schematic with PCB design using Cadsoft Eagle for a small arduino nano -like board with a single Atmega328 and ESP8266 (ESP-12) wifi module connected to each other using the Atmega USART. Atmega ICSP connector should be present somewhere on the board. A logic switch on the USART RX and TX ports should be available, controllable via a small jumper to break out the RX and TX to pins on the edge of the board for bootloader of both the Atmega and ESP-12 module. In normal operation the Atmega must be connected to the ESP-12. A sufficiently large linear regulator should step down the 5V Atmega supply to the 3.3V supply to the ESP-12. Resistors can be used to do logic level shifting between the Atmega nd ESP-12 module. A switch mode DC-DC should be present to conv...

We are looking for a developer for the ESP8266 WiFi Chip What we looking for: - Good programming knowledge - Good mood - Likes to work flexible and is not afraid to challenge new stuff What we provide: - Datasheets and SDK documentation - Current code and development environment

program is to be written in C using the MikroC PRO for PIC IDE. You must create a MikroC PRO for PIC project which may include one or more C source files. The testing is to be completed using: the Oshonsoft PIC18 simulator and/or the MikroC PRO for PIC debugger. More information will be share through PM. My budget is 55$ and deadline 2 days

Arduino Based System with Wifi ESP8266 Module to Switch On / Off Electrical Switches / Sockets

I need to have a tiny Web Server with the ESP8266 WiFi Module, your code so this module with it's sdk will act as an access point and will direct the visitors to a saved web site inside it. complete documentation needed upon completion. one milestone as i lost enough money by many who promise but do not deliver from freelancers and spend weeks figuring out answers.

Arduino Based System with Wifi ESP8266 Module to Switch On / Off Electrical Switches / Sockets

Hi i would like to rig up a simple circuit that can run as an open (no password) stand-alone access point/server (no internet connection needed or wanted) that can distribute a small packet of predefined text to any wifi enabled device. The text can be served through html or whatever is easier for the user. I want to use the esp8266 01 if possible, otherwise the 09 which has memory on board. I need to have a super-simple but energy efficient circuit to wire up (so diagram and instructions) and the tool chain (FTDI for usb code delivery) also the actual code to send to it through arduino IDE.

GPS Tracker scope of work. (Arduino bootloader compatible) Complete device to ru...work. (Arduino bootloader compatible) Complete device to run on 3-5v lipo battery 1) MCU Atmega 2560? 2) USB connection to program the MCU 3) ISP header to load Boot loader 4) PCB the smaller the better. 5) Ublox M8L GPS receiver with external antenna MMCX connector ,connected to serial port 3 6) Accelerometer sensor 7) Barometric pressure sensor 8) Lipo charger circuit. 9) ESP8266-05 wifi chip footprint connected to serial port2 serial 10) Lipo battery connection point (2 pin header) 11) Raw voltage input point for charging lipo 5-12vdc(2 pin header) 12) RGB status led 3 pin header for battery status indicator 13) Button input connection (2 pin header) 14) Buzzer (2 pin...

Project description: I would need piece of code for ESP8266 for arduino IDE 1.6.4. Process: First setup open Wifi AP with ESP8266 (()) and then when some client connects () serve a webpage form which allows to select one of the available AP and to enter its password. Then catch the submitted data and save it to EEPROM. Then restart and connect the ESP8266 to the saved WiFi AP. Test that the WiFi logon works, if not then return back to the open AP for another try. Include output progress to serial console.

Project description: I would need piece of code for ESP8266 for arduino IDE 1.6.4. Process: First setup open Wifi AP with ESP8266 and then when some client connects () serve a webpage form which allows to select one available AP and to enter its password. Then catch the submitted data and save it to EEPROM. Then restart and connect to the saved AP. Include output progress to serial console.

lift elevator or microwave simulation using proteus and mplab or mikroc

A software written in MicroC (ATMEL microcontroller compatible with Philips P89V51RD2) to interface nrf24L01. Software must use acknowledge feature of NRF24L01 for reliable data transmission/reception. Only one byte will be transmitted/received at a time AND there will always be one master (1 controller + 1 NRF's) and multiple slaves (1 controller + 1 NRF for each slave). The Upper 4 bytes can be stored as "long" (or as an array) in code memory and lower address byte as a "char" data type for master so that one master could communicate with 254 slaves. Function call for master - char TransmitNRF(char Address, char TxData) where address can be between 0x01 to 0xFF and also is the frequency channel selected for NRF. On the slave side only 4 upper address bytes...

An application in embedded C emulating an android app to send wifi commands to a wifi enabled photo camera. The android app connect with camera as DLNA client (the wifi connection is ad hoc and the camera is the base station) using UPNP protocol, when the android device connects with the camera can send commands to control it remotely. It is necessary to decompile or disassembly...base station) using UPNP protocol, when the android device connects with the camera can send commands to control it remotely. It is necessary to decompile or disassembly a .so file containing all the commands to use it in the new firmware, the other way is sniffing the wifi traffic between the two devices. Can be used any plattform (arduino, MCU, etc) and if possible a cheap wifi module (esp8266...

I want to combine some schematics what worked arduino. Designing pcb as small as posible ( 2 or 4 layers will be ok ) for wearable All schematics available , most of them from sparkfun and well documented. Schematics 1- Imu 2- Lipo Charger 3- Arduino Pro Micro 4-SPI Flash 5-ESP8266 wifi All parts SMD and small as posible Altium and eagle accepted. All nets and signals properly has to be named , segments uses nets or ports , all segments will be in dashed lines and named No mounting holes.

Hello I'm working into a project and I still didn't do the firmware, To help me save some time, I need someone to write the initialization code only. I'm using the PIC24F08KL302, my hardware: - Cristal 8MHz at OSC1 and OSC2: configure PLL to run at 32MHz; - No analog inputs; - RB0 and RB1 as ICSP; - Led_Status output at RB2; - Led_Kalive output at RA7; - Cluster_Trigger output at RA6; - Key_A input at RA0; - Key_B input at RA1; - Encoder_A input at RA4; - Encoder_B input at RB4; - Sensor input at RB7; - Interrupt on RA0, RA1, RA4 and RB4; Attached the format of file I use. I need it for the next hours.

I need have a tiny Web Server with the ESP8266 WiFi Module, your the code so this module will act as an access point and will direct the visitors to a saved web site inside it. if can do it without arduino just by-itself it would be much better.

I need a programmer that develop for us an application using the ESP8266 chip. Please contact if you have some experience with this device. Need experienced programmer with that device. Need to use internal CPU for specific process And needed to embedd in a MQTT network

An application in embedded C emulating an android app to send wifi commands to a wifi enabled photo camera. The android app connect with camera as DLNA client (the wifi connection is ad hoc and the camera is the base station) using UPNP protocol, when the android device connects with the camera can send commands to control it remotely. It is necessary to decompile or disassembly...base station) using UPNP protocol, when the android device connects with the camera can send commands to control it remotely. It is necessary to decompile or disassembly a .so file containing all the commands to use it in the new firmware, the other way is sniffing the wifi traffic between the two devices. Can be used any plattform (arduino, MCU, etc) and if possible a cheap wifi module (esp8266...

I need a programmer that develop for us an application using the ESP8266 chip. Please contact if you have some experience with this device.